Bathroom cabinets are a major piece of any bathroom furnishings

Medicine cabinets were initially created to work as useful holding areas for lotions, potions, and perfumes. Nobody can be entirely sure what time they ended up being moved into the bathroom, but for some reason that room was chosen to store the many sundry substances utilized in daily life. Medicine cabinets were plain in style and purpose and it is not until recent times that anyone gave some real attention as to how they looked.

Medicine cabinets nowadays are available in a extensive variety of types, sizes and finishes, so matching the look of your bathroom is simple. You can acquire medicine cabinets in square and rectangular shapes, recessed or surface mounted and in either wood finishes or metal finishes. You can even vary the location of your medicine cabinet. Gone are the days when they had to be centered above the bathroom sink.

When shopping for a new medicine cabinet you can check with just about any home products store, hardware store or big retail store and discover several types of medicine cabinets. On the other hand, if you desire the top selection and prices you must think about doing some research via the web ahead of making this purchase. There are many trustworthy online suppliers providing every type of medicine cabinet conceivable as well as they frequently charge less, since overhead is normally lower with Internet distributors.

There are two methods to install almost any cabinet: recessed or flush mounting and surface mounting. Recessed mounting must be left to a person who has done it before as it calls for cutting the wall open and possibly needing to cut the 2×4s if the cabinet exceeds 16 in. in width. Surface mounted medicine cabinets are installed quite easily by either fastening them straight to the 2×4s or installing some brackets and hanging them like hanging a picture on the wall. When installing your medicine cabinet it’s important to keep in mind that it could be somewhat heavy, so you will want to make certain it’s strongly attached to the wall studs. If this is the case, it will require you to use heavy duty brackets, which usually come with the cabinet.

The initial step is to find the 2×4s where you will be attaching the cabinet. If you have a stud finder (obtainable in most hardware store tool sections) find the middle of the two studs the cabinet will cover and mark the wall. If you don’t have a stud finder, get a small finishing nail and employ trial and error to find the 2×4s. Tap slightly with your finger on the wall in a horizontal direction until the sound lowers, then gently drive the nail in at least 3/4 in. to find out if you found air or wood. If you found wood, drive the nail in two more times, 1/2 in. to the left and right of the original hole. This way you will approximate where the center of the 2×4 is. It is not important that you find the center precisely, but you will want the screws to have a reliable “bite.” If for some reason you can not find the 2×4s you will require to use hollow wall anchors; the screw-in types are the simplest to work with and are especially solid. After that don’t be concerned about any of those small holes you made; the cabinet will cover them. Learn more about cabinets for the bathroom.

The following move is to line up the cabinet with the 2×4s. Position the cabinet with the top barely underneath your center marks or the holes and make certain it’s in the horizontal location you want. Do not be concerned about leveling it yet. Mark the top of the cabinet, then put it on the counter and draw two perpendicular lines from the marks on the top of the cabinet to the bottom. Drill the required holes on these two lines. Four holes should be enough, but if the cabinet is very heavy, make six or maybe eight holes. Author’s note: when it comes to hanging things on the wall, I firmly believe in “too much is barely enough”.

As soon as the holes have been drilled in the cabinet, line it up on the wall precisely where you need it, level it, check the position again, double check the level, and then mark the holes on the wall. Set the cabinet back on the counter, then using a drill bit that is roughly half the diameter of the screw, drill pilot holes in the wall where you marked them and then thoroughly screw the fasteners in, and then remove them. Be sure the holes are completely ready before mounting the cabinet. The basis for doing it in this fashion is to make holding the cabinet and fastening it in much easier, as well as more precise. Keep the cabinet in place, screw it in, make certain all screws are firm, tidy up the mess, and put your tools back in their place. Next, put stuff in the cabinet and you are finished. Learn more about wall tiles and bathroom vanity stool.

Bookmark to: